MIGHTY EXTRA
  No. 70 UPVC SOLVENT CEMENT No. 10 UPVC SOLVENT CEMENT HIGHT HEAT RESISTANT UPVC SOLVENT CEMENT
Solid Content 24% (Fast Drying) 24% (Slow Drying) 40% (Especially Slow Drying)
Consistency Property 1,000cps 1,000cps 3,000cps
Color Transparent Transparent Transparent
Quality Tough & Resillient Tough & Resillient Tough & Resillient
Standard MS628-4:2015 MS628-4:2015 MS628-4:2015
 
  • A highly soluble fast-dry UPVC solvent cement.
  • Suitable for joining all UPVC pipes from 15mm - 200mm diameter.
  • When applied, it will instantly dissolve and blend with the pipe to produce a film (wall) of 0.4mm thick, so that the fitting gap will be strong and stable.
  • A highly soluble slow dry UPVC solvent cement.
  • Suitable for joining all UPVC pipes from 75mm - 200mm diameter.
  • When applied, it will instantly dissolve and blend with the pipe to produce a film (wall) of 0.4mm thick, so that the fitting gap will be strong and stable.
  • A highly soluble slow dry UPVC solvent cement.
  • Suitable for joining non-standard UPVC pipes from 100mm diameter or where the UPVC pipe's fitting gap is too big.
  • When applied, it will instantly dissolve and blend with the pipe to produce a film (wall) of 0.8mm thick, so that the fitting gap will be strong and stable.
Straining Time
Pipes with diameter 15mm(1/2") 20 seconds
Pipes with diameter 25mm(1") to 32mm(11/4") 16 seconds
Pipes with diameter 50mm(2") 14 seconds
Pipes with diameter 75mm(3") 12 seconds
Pipes with diameter 100mm(4") 10 seconds
Pipes with diameter below 200mm(8") 6 seconds
Pipes with diameter 25mm(1") 30 seconds
Pipes with diameter 32mm(11/4") to 50mm(2") 20 seconds
Pipes with diameter 75mm(3") to 100mm(4") 15 seconds
Pipes with diameter 150mm(6") 10 seconds
Pipes with diameter 200mm(8") 6 seconds
Pipes with diameter 25mm(1") and above 60 seconds
Pipes with diameter 32mm(11/4") to 50mm(2") 50 seconds
Pipes with diameter 75mm(3") to 100mm(4") 40 seconds
Pipes with diameter 150mm(6") 30 seconds
Pipes with diameter 200mm(8") 20 seconds

ATTENTION

  1. Temperature below 15℃ (50℉) will extend the straining period for approximately 5 minutes for each type of pipe.
  2. All the above solvent cement are not applicable to those UPVC pipe or fitting which are made of partly recycled material.
  3. After assembly, the pipe must be tightly held in place and shall only be released after recommended straining time as stipulated. If release prematurely, the pipe to be fitted will spring apart.
PACKING Ctn. Size
3kg x 8 Tins per ctn. 440mm x 360mm x 260mm
500g (with brush) x 20 Tins per ctn. 508mm x 220mm x 225mm
100g (with brush) x 60 Tins per ctn. 508mm x 220mm x 225mm
14g x 240 Tubes per ctn. 508mm x 220mm x 225mm

SOLVENT CEMENT REQUIREMENT FOR UPVC PIPES & PVC FITTINGS

Nominal Size of Pipe or Fitting Amount of Solvent Cement required per joint Number of Possible Joints
ins mm g. 14g. 100g. 500g. 3kg.
1/2 16 1.3 10 76 383 2300
3/4 20 2.0 7 55 250 1500
1 25 2.5 5 40 200 1200
11/4 30 3.2 4 30 156 937
11/2 40 5.0 2 20 100 600
2 50 7.2 1 13 69 416
3 75 12.0 - 8 41 250
4 100 15.5 - 6 32 193
6 150 26.0 - 2 19 115
8 200 49.0 - 1 10 61
10 250 75.5 - - 6 39
12 300 108.0 - - 4 27
14 350 146.0 - - 3 20
16 400 200.0 - - 2 15
18 450 250.0 - - 2 12

DIRECTION FOR USE

1. Saw at the point to be mated, ensuring that the end of the pipe or fitting to form the spigot is cut at right angles to its axis. Remove any scarf and other debris from the joining surface.
2. Clean the mating surface with a suitable uPVC cleaning fluid.
3. & 4. Dip the clean brush (Please refer to recommendations on brush) into solvent cement and apply it evenly, by stroking along (and not round) the clean and dry mating surface.
 
5. Connect and fit the pipes to the mating surface properly and securely together. Avoid any vibration or movement until the recommended straining time is over.
6. Full pipes pressure can be applied in about twenty-four (24) hours after joining.


RECOMMENDATIONS ON BRUSH

  1. Pipes with diameter 25mm (1") and below - use brush as accompanied and affixed to can.
  2. Pipes with diameter 32mm to 50mm (1 1/4" to 2") - use seperate 1" brush.
  3. Pipes with diameter 75mm to 200mm (3" to 8") - use seperate 2" brush.

PRESSURE TEST

    TEST PRESSURE DRYING TIME
No. 70 & No. 10 Cold Water (20℃) Below 12kg/cm2 (171psi) After 10 hours
  Hot Water (60℃) Below 12kg/cm2 (171psi) After 24 hours
High Heat Resistant Cold Water (20℃) Below 10kg/cm2 (142psi) After 10 hours
  Hot Water (60℃) Below 10kg/cm2 (142psi) After 24 hours

MATERIAL SAFETY DATA SHEET

COMPOSITION / INFORMATION ON INGREDIENT
INGREDIENT PVC RESIN CYCLOHEXANONE (C.Y.C) METHYL ACETATE (MEAC) METHYL ETHLY KETONE (MEK)
CAS No. 9003-22-9 108-94-1 79-20-9 78-93-3
% - Volume 24% 26% 35% 15%

PHYSICAL AND CHEMICAL PROPERTIES

Appearance: Clear    Flash Point: 15℃    DG Class: 3.2
Flammable Mixture (UN No. 1133)
This solvent cement material will ignite at ambient temperatures. Colourless vapors may travel considerable distance to ignition sources and cause flash fires or explosions.

HAZARD IDENTIFICATION

May cause eyes and skin irritation, burns or dermatitis.

STORAGE

Store in well-ventilated area. Keep away from heat, sparks and flame.

SAFETY PHASE

  • Keep away from sources of ignition - No-Smoking.
  • Avoid contact with eyes.
  • In case of fire, use chemical powder, foam or carbon dioxide.